DI-9M-08CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
 |
  |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
 | Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
最新產品
- 科研檢測原理γ1肌動蛋白(ACTG1)ELISA試劑盒 2025/9/12 3:07:11
- 極威生物沙鼠田鼠昆蟲S抗原(SAG)ELISA試劑盒 2025/9/12 3:02:05
- 科研兔豬犬貓猴谷胱甘肽S轉移酶α5(GSTα5)ELISA試劑盒 2025/9/12 2:56:42
- 極威生物雞鴨鵝魚白介素19(IL-19)ELISA試劑盒 2025/9/12 2:51:10
- 科研兔豬犬貓猴糖皮質激素受體α(GRα)ELISA試劑盒 2025/9/12 2:46:01
- 極威生物豚鼠裸鼠倉鼠補體成分2(C2)ELISA試劑盒 2025/9/12 2:41:00
- 科研說明書甘露聚糖結合凝集素相關絲氨酸蛋白酶2(MASP2)ELISA試劑盒 2025/9/12 2:30:20
- 極威生物豚鼠裸鼠倉鼠血小板因子3(PF-3)ELISA試劑盒 2025/9/12 2:25:47
- 科研兔豬犬貓猴胱天蛋白酶14(CASP14)ELISA試劑盒 2025/9/12 2:19:59
- 科研沙鼠田鼠昆蟲普通轉錄因子IIB(GTFIIB)ELISA試劑盒 2025/9/12 2:14:39
- 科研精氨酸酶(ARG2)ELISA試劑盒實驗步驟 2025/9/12 2:10:26
- 極威生物豚鼠裸鼠倉鼠纖溶抑制因子(TAFI)ELISA試劑盒 2025/9/12 2:05:20
- 科研沙鼠田鼠昆蟲凝溶膠蛋白(GS)ELISA試劑盒 2025/9/12 1:59:17
- 科研說明書L苯丙氨酸解氨酶(PAL)ELISA試劑盒 2025/9/12 1:54:42
- 科研端粒重復結合因子1(TERF1)ELISA試劑盒樣本收集 2025/9/12 1:49:51
- 科研豚鼠裸鼠倉鼠血小板反應蛋白4(TSP-4)ELISA試劑盒 2025/9/12 1:43:47
- 極威生物牛馬綿山羊D-多巴色素變位酶(DDT)ELISA試劑盒 2025/9/12 1:39:04
- 極威生物豬犬貓猴載脂蛋白B編輯催化多肽1互補因子(ACF)ELISA試劑盒 2025/9/12 1:33:38
- 科研兔豬犬貓猴組蛋白H2b(histon-H2b)ELISA試劑盒 2025/9/12 1:28:06
- 科研豬犬貓猴5核苷酸酶(5-NT)ELISA試劑盒 2025/9/12 1:22:50
- 科研前梯度蛋白2(AGR2)ELISA試劑盒實驗步驟 2025/9/12 1:17:09
- 極威生物牛馬綿山羊毒蕈堿型乙酰膽堿受體(M-AChR)ELISA試劑盒 2025/9/12 1:12:15
- 科研雞鴨鵝魚血管緊張素II(Ang-II)ELISA試劑盒 2025/9/12 1:02:33
- 極威生物牛馬綿山羊分泌性白細胞肽酶抑制劑(SLPI)ELISA試劑盒 2025/9/12 0:55:16
- 極威生物豬犬貓猴基質金屬蛋白酶25(MMP-25)ELISA試劑盒 2025/9/12 0:50:29
- 科研白介素3(IL-3)ELISA試劑盒樣本收集 2025/9/12 0:45:33
- 科研牛馬綿山羊脂聯素(ADP/Acrp30)ELISA試劑盒 2025/9/12 0:40:13
- 極威生物豬犬貓猴基質金屬蛋白酶7(MMP-7)ELISA試劑盒 2025/9/12 0:32:46
- 科研實驗步驟細胞色素C氧化酶(COX)ELISA試劑盒 2025/9/12 0:28:14
- 科研實驗步驟基質細胞衍生因子2樣蛋白1(SDF2L1)ELISA試劑盒 2025/9/12 0:23:46